Current Position ：Home > Company News
Basic knowledge of daily use of polishing machine
Basic knowledge of daily use of polishing machine
1 the operation of the polishing machine:
(1) before polishing to remove the floor surface waste, and wet wipe to remove sand and gravel.
(2) check whether the polishing brush is clean and need to be replaced.
(3) check whether the controller is in the position of the normal speed.
(4) to switch on the power supply, the operation should be started from the nearest place of the power supply socket, and the walking route is a straight line, and the polishing ground should be overlapped on the ground.
(5) the machine down, and then loaded on the pad at the bottom of the machine.
(6) the body flat, so that the turntable together with the 100 clean pad close to the ground.
(7) to start the power switch, polishing back and forth.
(8) the polishing speed should be maintained at 50 m / min to polish 3-5 times.
(9) to overlap between rows and rows of 1/3, so as not to drain.
(10) after the use of the power switch off, remove the clean pad cleaning.
(11) good power line.
2 matters needing attention:
(1) don't drive too fast at work, so as to avoid collision.
(2) non flammable liquids can be used to wash the floor, or to operate a machine in an explosive atmosphere.
(3) operation of the machine, not to lift the operating lever, which will cause the machine out of control.
(4) the machine must be placed in the room, not rain and snow, can not make the machine to the top of any liquid spray.
(5) can not be pressed on the machine, because it has a precise balance, when the operation needs to move the operating standard, you must move all the wires.
(6) the ground wire must be connected with the switch box and motor, then the fault will result in electric shock.
3 the daily maintenance of polishing machine:
(1) after each use, the body should be cleaned.
(2) check if the power cord is damaged before operation.
(3) the wheels and other parts of the activities should be refueling 1 times a month.
(4) after each use, the cleaning shall be recorded on the day of use.
(5) after each use, use a clean cloth to wipe the surface of the machine, do not need to use a polishing pad on the drive plate, and disconnect the machine.
1 the operation of the polishing machine:
(1) before polishing to remove the floor surface waste, and wet wipe to remove sand and gravel.
(2) check whether the polishing brush is clean and need to be replaced.
(3) check whether the controller is in the position of the normal speed.
(4) to switch on the power supply, the operation should be started from the nearest place of the power supply socket, and the walking route is a straight line, and the polishing ground should be overlapped on the ground.
(5) the machine down, and then loaded on the pad at the bottom of the machine.
(6) the body flat, so that the turntable together with the 100 clean pad close to the ground.
(7) to start the power switch, polishing back and forth.
(8) the polishing speed should be maintained at 50 m / min to polish 3-5 times.
(9) to overlap between rows and rows of 1/3, so as not to drain.
(10) after the use of the power switch off, remove the clean pad cleaning.
(11) good power line.
2 matters needing attention:
(1) don't drive too fast at work, so as to avoid collision.
(2) non flammable liquids can be used to wash the floor, or to operate a machine in an explosive atmosphere.
(3) operation of the machine, not to lift the operating lever, which will cause the machine out of control.
(4) the machine must be placed in the room, not rain and snow, can not make the machine to the top of any liquid spray.
(5) can not be pressed on the machine, because it has a precise balance, when the operation needs to move the operating standard, you must move all the wires.
(6) the ground wire must be connected with the switch box and motor, then the fault will result in electric shock.
3 the daily maintenance of polishing machine:
(1) after each use, the body should be cleaned.
(2) check if the power cord is damaged before operation.
(3) the wheels and other parts of the activities should be refueling 1 times a month.
(4) after each use, the cleaning shall be recorded on the day of use.
(5) after each use, use a clean cloth to wipe the surface of the machine, do not need to use a polishing pad on the drive plate, and disconnect the machine.
Contact Supplier
